A rested roast chicken carves cleanly and stays juicier. Here is the kit, and seven stages, from snipping the string to the base cut, plus two other ways: breasts off whole, and the catering college method.
Let the bird rest in a warm place for 10 to 15 minutes after it comes out of the oven — the juices settle and the meat carves more cleanly. Have a sharp carving knife and a carving fork ready, and set the chicken on a board with a juice groove so the juices do not run over the table. Some cooks prefer a boning knife to take off the breasts and legs.
A carving knife with a long, thin, slightly flexible blade, freshly sharpened. A blunt knife only squashes the meat.
A boning knife (optional), for taking off the breasts and legs.
A carving fork with long tines. Use it mostly to steady the bird by pressing with the back of the fork; every stab lets juice out.
A board with a groove to catch the juices, and a damp cloth underneath so it does not slide. Those juices can go into the gravy.
When you carve, try to give everyone a little white meat and a little dark. If the thighs are generous you can slice some of that dark meat to go round. A small bird is often easiest simply halved or quartered. The stages below are for a family-sized roast. Work one side at a time, with long, smooth strokes rather than sawing at it.
Stage 1Remove the string
Snip away the trussing string and pull every piece away, so nothing is left to go to the table. Sit the chicken on its back, breast up, on the board. The method for tying the bird in the first place is on How to truss a chicken or turkey.
Illustration
Stage 2Cut the skin between leg and breast
Slide the knife through the skin between the thigh and the breast, close to the body, on both sides. Then, with the fork, roll the bird onto its side and carefully cut round the oyster — the neat nugget of dark meat in the hollow of the backbone — so it stays on the thigh when the leg comes away.
Stage 3Pop the hip joints on both sides
Spear the thigh with the two-pronged carving fork and twist the leg up and forwards until the hip joint pops. Cut through the joint and lift the leg away with the oyster attached, then do the same on the other side.
IllustrationIllustration
Stage 4Divide the legs at the joint
Split each thigh from its drumstick by cutting through the joint. A thin line of white fat on the underside shows you where the joint is.
Illustration
Stage 5Remove the wishbone
This is best done before cooking. If the wishbone is still in, ease it out now so you have a clear run at the breast.
Stage 6Carve the breast
Carve the breast in even slices, parallel to the rib cage, with long, smooth strokes.
Stage 7The base cut: take off the wing
Cut horizontally at the wing joint to take the wing off. Then turn the bird and repeat on the other side.
Method 2: breasts off whole (kitchen method)
A second way, handy when you carve in the kitchen and send the meat out on a platter. Stages 1 to 5 are the same as above: string off, skin cut, hip joints popped, legs divided and wishbone out. Then:
Method 2 · Stage 6Remove the wings
Cut through the wing joint on each side and take the wings off.
Method 2 · Stage 7Remove the breasts whole
Run the knife down one side of the breastbone, then follow the rib cage with short strokes, easing the breast away in one piece. Repeat on the other side.
IllustrationIllustration
Method 2 · Stage 8Remove the oysters with your fingers
If the oysters are still on the carcass, turn it over and pick them out of the hollows either side of the backbone with your fingers.
Method 2 · Stage 9Cut the breasts into thick slices
Lay each breast skin side up on the board and cut it across the grain into thick slices.
Illustration
Method 2 · Stage 10Arrange the board
Arrange the sliced breast in a tidy row, with the thighs, drumsticks and wings beside them. The oysters can sit with the dark meat. Send the meat out on a warm platter if you prefer not to carve at the table. The carcass can go for stock.
Illustration
Method 3: the catering college way
The method taught in many catering colleges. Stages 1 to 5 are the same as above. Then, one side at a time:
Method 3 · Stage 6Cut diagonally through the breast and wing joint
Cut diagonally through the breast, down through the wing joint, so the wing comes away with a portion of breast.
Method 3 · Stage 7Remove the remaining half breast
Ease the rest of the breast away from the rib cage in one piece.
Method 3 · Stage 8Remove the oysters
If the oysters are still on the carcass, pick them out with your fingers. Then repeat stages 6 to 8 on the other side.
A few useful tips
Keep it warm. A cold plate will cool the meat in no time. Warm the platter and send the slices up as soon as you have carved them.
Save the carcass. Once the meat is off, break up the carcass and simmer it for stock.
A larger bird. A roast turkey is carved in the same spirit, with a slightly different sequence — see How to carve a turkey.