Know HowCarving

Know How · Techniques

How to carve a ham

Two ways to carve a cooked ham or gammon on the bone: slice on the bone and then release those slices, or take off a boneless section and slice it on the board. The knuckle stays on the left throughout.

A carving knife following the bone of a cooked ham on a wooden board, with a fan of released pink slices lying to the left of the joint, the knuckle on the left.
Illustration

Before you start

Have a sharp carving knife and a carving fork ready, and set the ham on a stable board so it cannot slip. A damp cloth under the board helps. Work with the knuckle on the left, and keep the supporting hand clear of the blade.

  • A carving knife with a long, thin, slightly flexible blade, freshly sharpened. A blunt knife only squashes the meat.
  • A carving fork with long tines, to steady the joint.
  • A stable board, with a damp cloth underneath so it does not slide. A board with a juice groove is useful if the ham is still hot.
  • A platter for the carved slices.

More on choosing a blade: carving knives. For the bird, see How to carve a chicken and How to carve a turkey.

Slice on the bone, then release

Open a wedge, make thin parallel cuts, and release those same slices from beneath. The knuckle stays on the left throughout the sequence.

Method 1 · Step 1Open a wedge

Secure the ham on a stable board. Near the shank, cut down to the bone, then make an angled cut to meet it. Remove the small wedge to create working space.

A carving knife opening a small wedge near the shank of a cooked ham on a wooden board, with a pale oval of bone visible in the cut and a carving fork steadying the joint, the knuckle on the left.
Illustration

Method 1 · Step 2Make thin slices

From the opening, cut thin, evenly spaced slices down to the bone. Keep them attached at their base. Use a gentle back-and-forth motion; stop when the blade meets bone.

A carving knife cutting thin vertical slices down to the bone of a cooked ham, the slices still attached at their base, with a carving fork in the right of the joint and the knuckle on the left.
Illustration

Method 1 · Step 3Release the slices

Turn the blade to follow the bone underneath the prepared cuts. Free those same slices and transfer them to the platter. A clean exposed area replaces the attached slices.

A carving knife following the bone of a cooked ham to release a fan of pink slices, which lie overlapping on the left of the wooden board, the knuckle on the left.
Illustration

When to use it: for carving a whole joint at the table while keeping most of the ham intact. Work in small batches, then turn and secure the ham to reach the remaining meat.

Technique references: New Zealand Woman’s Weekly: wedge opening; RecipeTips: carving ham.

Remove a section, then slice

Separate a boneless section from the cooked joint first, then slice it on the board. The remaining ham stays on the bone.

Method 2 · Step 1Follow the bone

Steady the ham with a fork. Cut closely along the bone to free a substantial section of meat, following natural muscle divisions where helpful. Keep the section in one piece.

A carving knife cutting closely along the bone of a cooked ham from the shank, showing a pale bone in the opened seam, with a carving fork steadying the joint and the knuckle on the left.
Illustration

Method 2 · Step 2Set the section down

Finish separating the meat and place it flat, cut-side down, on the board. The detached piece is boneless; the bone remains in the main joint. Reposition the fork to steady the piece.

A boneless section of glazed ham set down in front of the joint on a wooden board, the main joint behind showing a pink cut face and a pale bone stump, with the knife and fork on the detached piece and the knuckle on the left.
Illustration

Method 2 · Step 3Slice across the grain

Cut thin, even slices across the detached section, using the length of the knife. Adjust the direction for each muscle section. Repeat with other sections as needed.

A carving knife slicing a detached boneless section of ham across the grain, with four thin slices already lying on the left of the board, the remaining joint behind, and the knuckle on the left.
Illustration

When to use it: for convenient portioning and more consistent slices. The ham can still have been cooked on the bone. Keep the board stable and the supporting hand clear of the blade.

Technique reference: Silver Star Meats: How to Carve a Ham (section removal and slicing).

The illustrations show the sequence of actions; the exact bone position and muscle shape vary with the joint.

See also